- 모듈 추가로 다양한 측정과 채널 확장 (최대 1120CH)
- 측정 모듈 확장에도 동일한 샘플링 속도 유지
- 측정 시그날: 전압, 온도, Logic/pulse 모듈
- 탈부착 가능한 5.7인치VGA 디스플레이 모니터
- STAND ALONE 또는 시스템 설비화 가능
- 측정 Application에 맞는 데이터 저장 위치 선택 가능

스마트 데이터 수집장비

특징 1 - Module 확장으로 다양한 측정!

각종 앰프모듈에 따라, 측정대상 및 채널수 확장

측정 앰프모듈 확장에도 샘플링 속도 유지

측정 앰프모듈 확장에도 샘플링 속도 유지

추가로 다채널 측정을 원할 때

특징 2 - 다양한 신호의 동시 계측 가능!

1. 내장 RAM

2. 내장 플래시 메모리

3. SD 카드

4. 64GB SSD모듈 (옵션)

특징 4 - PC접근이 간편한 인터페이스

Web server / FTP server 기능

특징 5 - 고감도 터치패널 디스플레이 모듈 장착

탈부착 가능한 디스플레이 모듈로 Stand-alone 및 시스템 설비화 OK!

고감도 터치패널 방식으로 조작성 UP!

설정 조작이 쉬운 터치패널

고화질 대형 5.7인치 VGA(640*480)모니터의 선명한 모니터링 OK!

간편한 조작과 다기능 PC 소프트웨어를 기본제공!

다양한 화면설정

멀티윈도우 기능으로 한 화면에 전체 측정 파형 및 지정 파형을 동시 확인

특징 6 - 편리한 기능 - 데이터 처리에 편리한 각종 기능을 내장

GL7000 main unit specifications

Item		Description
Number of module		Attached to up to 10 modules *1
Number of input channels		Max. 112 channels in one GL7000
External Input/Output signals *2	Input	Start/Stop, Trigger, External sampling, Auto balance Signal type: Contact (relay), Open collector, Voltage
	Output	Trigger, Busy, Alarm (10 channels) *3 Signal type: Open collector (pulled-up by resistor 10 k ohms)
Trigger, Alarm function	Trigger repeat	Enabled (ON): Automatically rearm for the next data capture Disabled (OFF): Data capture is completed in a single trigger
	Trigger action	Start or stop capturing data by the trigger
	Trigger condition	Start: Off, Measured signal, Alarm, External, Clock, Week or Time Stop: Off, Measured signal, Alarm, External, Clock, Week or Time
	Trigger determination conditions for measured signal	Combination: OR or AND condition at the level of signal or edge of signal Analog: Higher/Rising, Lower/Falling, Window-in, Window-out Logic *4: Higher/Rising, Lower/Falling Pulse *4: Higher/Rising, Lower/Falling, Window-in, Window-out
	Alarm determination condition *5	Combination: OR or AND condition at the level of signal or edge of signal Analog: Higher/Rising, Lower/Falling, Window-in, Window-out Logic *4: Higher, Lower, Rising, Falling Pulse *4: Higher/Rising, Lower/Falling, Window-in, Window-out
	Alarm output	10 channels
	Pre-trigger *6	Number of data before trigger: Up to specified number of captured data
Calculation function	Between channels	Addition, Subtraction, Multiplication and Division for two analog inputs (Sampling speed is limited up to 10 Samples/s (100ms interval). Available arithmetic element and the output destination is the analog input channel 1 to 100.)
	Statistical	Select two calculations from Average, Peak, Max., Min. in real time and replay *7
Move function of the display range		Beginning, center or end of the data, Trigger point, Specific time (absolute, relative), Call cursor
Search function		Search for analog signal levels, logic signal pattern, pulse signal levels or alarm point in captured data
Annotation function		Comment can be set in each channel (up to 31 alphanumeric characters)
Message, Marker function		Message: Record up to 8 messages in any timing (Any message can be set before data capture is started or during data capture.)Marker: Recorded when the trigger, alarm or power failure occur
Resume		Resume automatically in the same condition after power is recovered when the power failure occurred duaring data capture *8
Interface to PC		Ethernet (10 BASE-T/100 BASE-TX), USB 2.0 (High speed)
Network function		WEB server, FTP server, FTP client, NTP client, DHCP client
USB drive mode		Emulate the USB memory device *9
Storage device	Built-in	RAM (2 million samples, built-in Signal conditioning module), Flash memory (2 gigabytes, built-in the main module)
	External *10	SD card (Support SDHC, up to 32 GB) slot, SSD (Approx. 64 GB)The file for capturing data is limited up to 2 GB.
Data saving function	Captured data *10	Built-in RAM, Built-in Flash, SD memory card, SSD (Data is saved directly to it.)
	Data in built-in RAM	Specified number of data up 2 million samples increment of 1
	Auto save *10	Available for the built-in RAM Enabled (ON): Data in the RAM is saved automatically to the built-in Flash, SD memory card, SSD Disabled (OFF): Data in the RAM is not maintained after power is turned off
	Ring capturing mode *10 *11	Saves most recent data Number of capturing data: 1000 to 2000000 points, Destination of data: Built-in RAM, Built-in Flash, SD memory card, SSD
	During capturing data	Displaying information in two windows, Hot-swapping the SD memory card, Saving data in between cursors.
	Backup *10	Backup interval: Off, 1, 2, 6, 12, 24 hrs. Data destination: SD memory card, SSD, FTP server
Engineering Scale function		Measured value can be converted to the engineering unit  Analog voltage: Converts by four reference points (gain, offset) Temperature: Converts by two reference points (offset) Pulse count: Converts by two reference points (gain)
Synchronization between units		Start and Trigger *12
Accuracy of clock (at 23 degree Celsius)		+/- 0.002 % (Monthly deviation approx. 50 sec.)
Operating environment		0 to 45 ºC, 5 to 85 % RH (non condensed)
Power source		100 to 240 V AC, 50/60 Hz
Power consumption		Approx. 85 VA
Standard accessories		Quick guide, CD-ROM, AC power cable
External dimensions (W x D x H)		Main module: Approx. 193 x 141 x 160 mm (Excluding projectin), Alarm output terminal: Approx. 30 x 136 x 145 mm (Excluding projection)
Weight		Main module: Approx. 2 kg, Alarm output terminal: Approx. 350 g

※ 자세한 옵션은 카다로그 확인 요망!